The guide

Everything on radiator covers.

Fifteen years of craft, condensed onto one page. Measuring, materials, heat retention, and how to install.

Contents

  1. → How to measure
  2. → Material comparison
  3. → Heat output
  4. → Installation
  5. → Care & cleaning
  6. → Shipping & returns
  7. → Warranty
  8. → FAQ
Step 1

How to measure correctly.

A perfect fit depends on three measurements: width, height, depth.

Width

Measure between the outermost points of your radiator — including valves, supply pipes and brackets. Add at least 3 cm clearance on each side so the cover can be removed easily.

Height

From the floor to the top of the radiator. The slat arms run above the radiator, so measure to its highest point, including bleed valves.

Depth

From the wall (pipe entry) to the front edge of the radiator. Add 2–3 cm for air circulation.

Pro tip

Send us a photo of your radiator with a tape measure — we'll check your numbers for free and reply within 24 hours.

Step 2

Oak vs. MDF vs. Metal.

Three materials, three worlds. Here's why solid oak is the only choice that doesn't end up in a skip after three years.

Criterion Solid Oak MDF / Particleboard Metal
DurabilityDecades3–8 years10–15 years
Heat outputopen – warm air rises freelyoften closed – heat builds upperforated – depends on the hole area
AestheticDesign piece, ages wellSmooth, painted or foiledCold, industrial
RepairableYes, sand & re-oilNo, damage staysDifficult
Environment100 % naturalEngineered board with bindersEnergy-intensive
Value retentionHoldsLowLoses partly
Step 3

Understanding heat output & convection.

The biggest fear with radiator covers: "Will my room get colder?" The honest answer: it depends on the construction. What matters is that warm air can escape at the top and cool air can flow in at the bottom.

How a radiator really heats

A panel radiator emits most of its heat through convection (warm air rising), the rest through radiation. Block convection with a closed box and the warm air gets trapped – far less heat reaches the room.

Why our design works

Our 30 mm slats have 15 mm of air between them – about a third of the front is open, and the cover is fully open at the top and sides. Warm air rises unobstructed; cold air enters at the base. So heat loss stays low.

Step 4

15-minute installation.

No tradesman needed: rail on the wall, cover on the rail, done.

Unpack

Open packaging. Take piece out carefully and let it acclimatise in the room for 24 hours.

Fit the rail

Hold the wall part of the hanging rail level, mark the holes, drill (6 mm), plug and screw it tight.

Hang it

Lift the cover and set it onto the rail from above. The rail sets the position – level it once and everything sits straight.

Done

That's it. Take a photo, let your guests ask "where did you get that?"

The hanging rail is always included. Screws and wall plugs can be added in the configurator as a fixing kit (€32) – or use your own to suit your wall. You'll need a 6 mm drill bit either way. To read the heat meter or to clean, simply lift the cover off.

Step 5

Care & cleaning.

Solid oak is low-maintenance — but a little care doesn't hurt.

Everyday cleaning

Dust with a soft cloth or hoover with a brush attachment. For marks: a slightly damp cloth is enough.

Re-oil every 1–2 years

Oiled and natural variants benefit from re-oiling with linseed or hard-wax oil. A bottle of our care oil is available for €12.

For scratches

Light scratches sand out with grit 240+ paper, then re-oil. Deeper scratches: let us know, we'll send a free repair kit.

Shipping & returns

How we deliver — and how to return.

Shipping

Returns

Private customers can return standard sizes within 100 days of delivery for any reason — full refund. We collect for free. Bespoke pieces are made just for you, so the fit guarantee applies: if it doesn't fit to the millimetre, we take it back.

Warranty

What we promise.

100-day fit guarantee

Cover doesn't fit perfectly? We collect and refund in full. No risk.

5-year material warranty

On wood and workmanship. Cracks, warping, finish issues — we repair or replace for free.

FAQ

The 12 most common questions.

Solid oak – solid wood, no veneer, no plastic.
Width, height and depth of your radiator. Add 3–5 cm clearance on each side. Unsure? Send us a photo, we check it free.
Hardly – the cover is open at the top and sides, with 15 mm of air between the slats. Warm air rises freely.
Lead time 4–5 weeks for standard sizes and bespoke pieces alike, as every piece is made to order. Shipping & packaging within Germany from €29.90 depending on size.
Yes — up to 250 × 120 cm via the configurator. Larger or L-shapes: write to us, we'll quote in 24 hours.
Four finishes: Natural (untreated), Oiled (linseed), Smoked (fumed oak), White-pigmented.
Yes — we send a free sample set with all four finishes. Request via contact form.
Dust with soft cloth. Re-oil every 1–2 years. Scratches: lightly sand and re-oil.
Securely via Stripe: card (Visa, Mastercard) plus the methods offered at checkout (e.g. Klarna, PayPal). B2B terms on request.
Yes. Shipping to Austria, Switzerland and the EU is quoted individually on request. UK: prices in GBP via the region switch in the shop.
Yes – for interior studios, retailers and design practices through our partner programme (referral commission or trade account). Projects: [email protected].
With normal use, decades. Solid oak is one of the hardest European hardwoods — same lifespan as a fine dining table.

Question not here?

Ask us →

Ready to configure your cover?

Live price · Instant order · 100-day fit guarantee · Shipping & packaging from €29.90.

Start now →